Epoxy Floor Coating and Protective Coatings

DESCRIPTION

SYSCOAT 551 is a two component Solvent free Epoxy Coating. The final film provides a glossy finish which is non-toxic. Can be coated in various thickness from 200 microns to 500 microns.

ADVANTAGES

• Anti —Skid in nature.
• Excellent resistance to Sea water and sewage water.
• Hygienic in Nature.
• Durable.
• Low maintenance cost.
• Non -shrink in nature.
• Can withstand temperature change.
• Chemical Resistant.
• Provides a Seamless floor Coating.

AREAS OF APPLICATION

SYSCOAT 551 is applied in areas like Reservoirs, Pharma & Bulk Industries, Aquaculture plants, Laboratories, Food processing units, Distelliers, Hospital & Computer Clean rooms, and as a protective coating in Paper and pulp Industry.
Chemical resistance Chart SYSCOAT 551 is resistant to various range of Chemicals. Data is available on request.

PROPERTIES
Pot Life:30 Minutes at 30 degrees Centigrade.
Initial Cure:24 Hours.
Final Cure:7 days at 30 degrees Centigrade.
Interval between Coats:24 Hours.
METHOD OF USAGE
SURFACE PREPARATION

The Surface should be cleaned, dried, and free from loose particles. Concrete surface must be free from latence and it can be removed from sand blasting. The surface must not contain a moisture content more than 4%. The surface has to be subjected to acid etching by using SYSCONS range of cleaning agents followed by washing with clean water.

MIXING

The mixing of both Resin and Hardener has to be done by using Mechanical stirrer in order to avoid any sort of settlement. The contents of Hardener has to be poured in to the Base Resin and the mixing has to be done for at least Three minutes.

PRIMING

For Cementitious surfaces SYSCOAT 555 or SYSCOAT 554 has to be used. For Metal surfaces SYSCOAT 553 has to be used.

TOP COAT

Apply the mixed SYSCOAT 551 over the dried primed surface. Make sure that a continuous film is achieved by using a standard paint Brush, good quality lambswool roller or with an airless spray equipment. The optimum dry film thickness can be achieved in two coats.

COVERAGE

At 200 microns thickness the coverage will be around 4 to 5 Sq. mtrs per Kg.

CLEANING

Clean all tools and equipment with Cleaning agents or Acetone immediately after the use.

SUPPLY

1 Kg & 2.5 Kg Packs.

SHELF LIFE

12 Months from the date of the Manufacture.

PRECAUTIONS

SYSCOAT 551 should be applied with gloves and care should be taken to see that it does not fall on the eyes.
Splashes on to the skin has to be removed immediately with a resin removal cream and medical advice has to be taken.

TECHNICAL SUPPORT

Technical information and guidance regarding SYSPLAST range of Admixtures, SYSGROUT range of Cementitious and Epoxy Grouting Systems, can be obtained from the technical cell of SYSCONS.

NOTE

Information in this Technical data sheet is to the best of our knowledge true and Accurate. However such conditions under which our products may be used or obtained beyond our control, recommendations are made without Warranty or Guarantee.

DESCRIPTION

SYSCOAT 552 is a two component Epoxy resin based Coating specially formulated to provide a durable coating suitable for application in both vertical & horizontal surfaces. The final high build coating provides a good resistance to a wide range of Acids, Alkalies and Solvents.

ADVANTAGES

• Excellent Adhesion.
• Excellent Chemical resistance.
• Hygienic in Nature.
• Abrasion resistance.
• Glossy, Smooth & Easy to clean surface.
• Non -Shrink in nature.
• Chemical Resistant.
• Provides a Seamless floor Coating.
• Effective on both Concrete & Metal surfaces.

AREAS OF APPLICATION

SYSCOAT 552 can be used as surface lining of tanks, Concrete walls, Metal tanks, Chemical plants, Battery rooms, Laboratories, Sluices, Ducts and as a protective coating in paper and pulp Industry.

CHEMICAL RESISTANCE CHART

SYSCOAT 552 is resistant to various range of Chemicals. Data is available on request.

PROPERTIES
Pot Life:30 Minutes at 30 degrees Centigrade.
Initial hardness:24 Hour sat 30 degrees Centigrade.
Final Cure:7 days at 30 degrees Centigrade.
Time Interval between Coats:24 Hours.
METHOD OF USAGE
SURFACE PREPARATION

The Surface has to be structurally sound, dry and free from any sort of loose material. Concrete surface has to be free from laitance and it can be removed from sand blasting. The surface must not contain moisture content more than 4%. The surface has to be subjected to acid etching by using SYSCONS range of cleaning agents followed by washing with clean water.

MIXING

The mixing of both Resin and Hardener has to be done by using Mechanical stirrer in order to disperse any sort of settlement. The content of Hardener has to be poured in the Base Resin and the mixing has to be done for at least Three minutes.

PRIMING

For Cementitious surfaces SYSCOAT 555 or SYSCOAT 554 has to be used. For Metal surfaces SYSCOAT 553, a Zinc rich primer has to be used.

TOP COAT

Apply the mixed SYSCOAT 552 over the dry primed surface. Make sure that a continuous film is achieved by using a standard paint Brush, good quality lambswool roller or with airless spray equipment. The optimum dry film thickness can be achieved in two coats.

COVERAGE

At 200 microns thickness the coverage will be around 2.8 Sq.Mtrs per Kg.

CLEANING

Clean all tools and equipment with SYSCONS range of Cleaning agents or Acetone immediately after the use.

SUPPLY

1 Kg & 2.5 Kg Packs.

SHELF LIFE

12 Months from the date of the Manufacture.

PRECAUTIONS

SYSCOAT 552 should be applied with gloves and care should be taken to see that it does not fall on the eyes which may lead to irritation & damage to the eyes. Any eye contamination should be washed with plenty of clean water and medical advice has to be taken.

TECHNICAL SUPPORT

Technical information and guidance regarding SYSBOND range of Bonding Agents, SYSFLOOR range of Epoxy Floorings, SYSGROUT range of Cementitious and Epoxy Grouting Systems can be obtained from the Technical cell of SYSCONS.

NOTE

Information in this Technical data sheet is to the best of our knowledge true and Accurate. However such conditions under which our products may be used or obtained beyond our control, recommendations are made without Warranty or Guarantee.

DESCRIPTION

SYSCOAT 555 is a two component Solvent free Epoxy Resin Primer. The final film provides a glossy finish which is non- toxic & has good Penetrating properties.

ADVANTAGES

• Anti —Skid in nature.
• Durable.
• Non -Shrink in nature.
• Chemical Resistant.
• Provides a Seamless floor Coating.

AREAS OF APPLICATION

SYSCOAT 555 is applied as Primer in areas like Reservoirs, Pharma & Bulk Industries, Laboratories, Food processing units, Distelliers, Hospital & Computer Clean rooms, and as a protective coating in paper and pulp Industry.

CHEMICAL RESISTANCE CHART

SYSCOAT 555 is resistant to various ranges of Chemicals. Data is available on request.

PROPERTIES:
Pot Life:40 Minutes at 30 degrees Centigrade.
Over Coating Time:24 Hours at 30 degrees Centigrade.
METHOD OF USAGE
SURFACE PREPARATION:

The Surface should be clean, dry & free from loose particles. Concrete surface must be free from laitance and it can be removed from sand blasting. The surface should not contain moisture content more than 4%. The surface has to be subjected to acid etching by using SYSCONS range of cleaning agents.

MIXING:

The mixing of both Resin and Hardener has to be done by using Mechanical stirrer in order to disperse any sort of settlement. The content of Hardener has to be placed in the Base Resin and the mixing has to be done properly to obtain a homogeneous material.

APPLICATION:

Apply the mixed SYSCOAT 555 over the dried primed surface. The applied surface should be at least 28 days old. Make sure that a continuous film is achieved by using a standard paint Brush, good quality lambswool roller or with airless spray equipment.

COVERAGE:

The coverage of SYSCOAT 555 will be around 5 to 6 Sq.mtrs per Kg.

CLEANING:

Clean all tools and equipment with Cleaning agents or Acetone immediately after the use.

SUPPLY:

1 Kg & 3 Kg Packs.

SHELF LIFE:

12 Months from the date of the Manufacture.

PRECAUTIONS:

SYSCOAT 555 should be applied with gloves and care should be taken to see that it does not fall on the eyes. 
Splashes on to the skin have to be removed immediately with a resin removal cream and medical advice has to be taken.

TECHNICAL SUPPORT

Technical information and guidance regarding SYSPLAST range of Admixtures, SYSGROUT range of Cementitious and Epoxy Grouting Systems, can be obtained from the technical cell of SYSCONS.

NOTE

Information in this Technical data sheet is to the best of our knowledge true and Accurate. However such conditions under which our Products may be used are obtained beyond our control, recommendations are made without Warranty or Guarantee.

DESCRIPTION

SYSCOAT 556 is a two component Water based Epoxy Resin coating. Part A consists of Base Epoxy Resin & the other Part B consists of Hardener which gives a Non toxic, Food Grade coating. SYSCOAT 556 can be applied in two coats. It can also be applied on the damp surface.

ADVANTAGES

• Water dilutable.
• Good penetration in to the Concrete surface.
• Dust free, Seamless coating.
• Resistant to Saltwater, Soap water.
• Resistant to Hydrostatic Water pressure.
• Non -Toxic & Eco friendly.

AREAS OF APPLICATION

SYSCOAT 556 can be used wherever dust free food grade epoxy coating is required like in different tanks of Aquaculture units, Food processing units, Reservoirs, Dairies, Distillers, Water treatment plants, Hatcheries.

PROPERTIES
Product:Two Component (Base & Hardener).
Mixing Ratio:PartA : PartB : Water = 1:1:1
Pot life:30 Minutes to 45 Minutes at 30 °Centigrade.
Initial Cure:1 Day at 30°Centigrade.
Final Cure:6 Day at 30°Centigrade.
Over Coating Time:24 Hours.
DIRECTIONS FOR USE
SURFACE PREPARATION

The Surface should be cleaned, and free from loose particles. Concrete surface must be free from Laitance, Grease, Oil, Fungus etc., by thorough wire brushing followed by sanding with emery paper.

MIXING

The mixing of both Part A and Part B has to be done by using Mechanical stirrer in order to disperse any sort of settlement till a homogeneous mixture is obtained.

APPLYING

The mixed material is brushed on to the well prepared surface by using a standard paint brush or good quality lambswool roller.
Proper care should be taken to ensure continuous film and proper material consumption.

COVERAGE

The Coverage of the material at 100 Micron thickness will be around 10 Sq.Mtrs/Kg.

CLEANING

Clean all tools and equipment with Cleaning agents orAcetone immediately after the use.

SUPPLY

SYSCOAT 556 is Supplied in 1 Kg & 5 Kg Packs.

SHELF LIFE

12 Months from the date of the Manufacture.

PRECAUTIONS

SYSCOAT 556 should be applied with gloves and care should be taken to see that it does not fall on the eyes. 
Splashes on to the skin has to be removed immediately with a resin removal cream and medical advice has to be taken.

TECHNICAL SUPPORT

Technical information and guidance regarding SYSPLAST range of Admixtures, SYSGROUT range of Cementitious and Epoxy Grouting Systems, can be obtained from the Technical cell of SYSCONS.

NOTE

Information in this Technical data sheet is to the best of our knowledge true and accurate. However, such conditions under which our products may be used or obtained beyond our control, recommendations are made without Warranty or Guarantee.